--- title: "How to Install Self-Closing Hinges" description: "On this page[Introduction](#)[Before You Begin](#)[Prerequisites](#)[What You Need To Know](#)[Tools Required](#)[Power Tools](#)[Hand Tools](#)[Supplies](#)[Materials](#)[Installation Steps](#)[Step 1: Confirm the Door and Hinge Locations](#)[Step 2: Remove and Replace the Top Hinge](#)[Step 3: Remove and Replace the Bottom Hinge](#)[Step 4: Set the Spring Tension](#)[Step 5:…" url: "https://letsbuildstuff.co/learn/install-self-closing-hinges/" updated: "2026-09-25" category: Hardware tags: - Core Guide - Level 1 --- # How to Install Self-Closing Hinges On this page[Introduction](#)[Before You Begin](#)[Prerequisites](#)[What You Need To Know](#)[Tools Required](#)[Power Tools](#)[Hand Tools](#)[Supplies](#)[Materials](#)[Installation Steps](#)[Step 1: Confirm the Door and Hinge Locations](#)[Step 2: Remove and Replace the Top Hinge](#)[Step 3: Remove and Replace the Bottom Hinge](#)[Step 4: Set the Spring Tension](#)[Step 5: Test the Full Operation](#)[Close-Out](#)[Quality Check](#)[Troubleshooting](#)[Door Doesn't Latch on Its Own](#)[Door Slams Shut](#)[Door Binds After the Hinge Swap](#)[Door Won't Move At All](#)[Middle Hinge Squeaks or Binds After the Swap](#)[Related Guides](#) [Hardware](/learn-category/hardware/) Skill Level: [Beginner (Level 1)](/learn/difficulty-levels/#level-1) · Estimated Time: 15-20 Minutes Per Door ## Introduction A [self-closing hinge](/glossary/hardware/#self-closing-hinge) uses a spring inside the hinge barrel to pull the door shut on its own, without a separate door closer mounted on the frame. At Sun's Up, these go on house-to-garage doors only, on the top and bottom hinge, with the middle hinge left as a standard [butt hinge](/glossary/hardware/#butt-hinge-leaf-knuckle-barrel-pin). That's a code requirement, not a style choice: the [International Residential Code (IRC)](https://codes.iccsafe.org/content/IRC2021V3.0/chapter-3-building-planning) requires the door between the house and the garage to self-close and latch, so a door left open by mistake doesn't leave the conditioned house and the garage connected. This guide covers swapping in self-closing hinges on an already-hung door, priced and installed per door. If you're hanging a new house-to-garage door from scratch, install the self-closing hinges as part of that process using the same top-and-bottom placement described here; see the [exterior door guide](https://letsbuildstuff.co/learn/install-exterior-door/) for the full hang. Because this is a code item, it gets checked at final walkthrough along with the rest of the house-to-garage door's safety details. A door that fails to self-close and latch is a straightforward fix at rough or trim stage, but it is a much bigger headache to catch after the drywall, paint, and flooring are all finished around it, so treat this step as part of hanging the door, not an afterthought. ## Before You Begin ### Prerequisites - The door is hung, swinging freely, and confirmed to be a house-to-garage door; this hardware doesn't belong on interior room doors - Self-closing hinges are on site, sized to match the existing hinge leaf, same height and width as the standard hinges already on the door - You know which hinges are top, middle, and bottom before you start pulling anything apart - All hinges and pins for the door are counted and on hand before you start, so a missing piece doesn't stall the swap partway through. ### What You Need To Know - Self-closing hinges go on the top and bottom hinge only. The middle hinge stays a standard butt hinge; it doesn't need to help with the closing spring - Swap one hinge at a time, starting with the top or bottom, never both at once. The remaining standard hinges keep the door supported and aligned while you work - Most self-closing hinges have an adjustable spring tension, set with a small tool inserted into the hinge knuckle. Confirm the adjustment method for the specific hinge you're installing before you start - If a hinge pin is missing, snap a piece of shoe nail to length with a pair of dikes (diagonal cutting pliers) and use it as a substitute pin - The door has to close fully and latch from any open position, not just from a few inches. Test from wide open, not just from a slight crack - If the [door casing](/learn/install-exterior-door-casing/) overlaps a hinge mortise, notch it back with a chisel so the hinge sits flush ## Tools Required ### Power Tools - [Drill/driver](/glossary/tools/#cordless-drill) ### Hand Tools - Screwdriver, Phillips and flathead - Adjustment tool or spanner for the hinge spring tension, usually included with the hinge kit - Chisel, for notching the door casing if it overlaps a hinge mortise ### Supplies - Hinge screws matching the existing mortise, or slightly longer if the mortise needs a firmer bite ### Materials - Self-closing hinges, Acorn brand, sized to match the door's existing hinges, top and bottom only ## Installation Steps ### Step 1: Confirm the Door and Hinge Locations Confirm this is a house-to-garage door before you touch anything; self-closing hinges don't belong on interior doors. Identify the top, middle, and bottom hinges. You'll be replacing the top and bottom only. ### Step 2: Remove and Replace the Top Hinge With the door still supported by the middle and bottom hinges, remove the top hinge pin and take out the old hinge leaf. Install the self-closing hinge leaf in the same mortise, using the existing screw holes where they line up. Reinsert the pin and check that the door still hangs correctly before moving to the next hinge. ### Step 3: Remove and Replace the Bottom Hinge Repeat the same process at the bottom hinge, keeping the door supported by the middle hinge while you work. Reinsert the pin once the new hinge leaf is seated and screwed in. ### Step 4: Set the Spring Tension Using the hinge's adjustment tool, set the spring tension so the door closes fully and latches from a fully open position. Test from a few different open positions, not just one. The door should close with enough force to latch, without slamming hard enough to be a hazard. ### Step 5: Test the Full Operation Open the door to several different positions and let go each time, confirming it closes and latches on its own from all of them. Check that the door doesn't bind or drag anywhere in its swing with the new hinges installed. ## Close-Out Confirm all hinge screws are tight and the pins are fully seated. Note on the door schedule or punch list that self-closing hinges are installed and tested, since this is a code item that gets checked at final walkthrough. ## Quality Check - Top and bottom hinges are self-closing; middle hinge is a standard butt hinge - Door closes and latches fully from any open position - Door doesn't slam hard enough to be a hazard - Door swings freely with no binding from the new hinges - All hinge screws are tight and pins are fully seated - [Strike plate](https://letsbuildstuff.co/learn/install-a-lockset/) is aligned with the latch ## Troubleshooting ### Door Doesn't Latch on Its Own Spring tension is set too light. Increase the tension with the adjustment tool and retest from a fully open position. ### Door Slams Shut Tension is set too high. Back it off gradually, testing after each adjustment, until the door closes firmly but doesn't slam. ### Door Binds After the Hinge Swap Check that the new hinge leaf seated fully in the existing mortise. A hinge sitting proud of the mortise will bind the door against the frame. ### Door Won't Move At All The spring may be installed or tensioned backward. Check the hinge manufacturer's instructions for the correct spring-loading direction before adjusting further. ### Middle Hinge Squeaks or Binds After the Swap The standard middle hinge itself did not change, so a new squeak there usually just means the door's weight shifted slightly onto it while you were working on the other two. Cycle the door a few times and recheck; if it persists, confirm the middle hinge screws are still fully seated. ## Related Guides - [How to Install a House-to-Garage Door](https://letsbuildstuff.co/learn/install-exterior-door/) - [How to Install a Pre-Hung Door](https://letsbuildstuff.co/learn/install-pre-hung-door/) - [How to Install a Door Bump](https://letsbuildstuff.co/learn/install-door-bump/) Written by **David Hospodka**, Sun’s Up Construction David Hospodka learned finish carpentry from his father, alongside his brother Joel, and worked his way through college trimming houses. He then spent about ten years as a railroad bridge engineer, handling design, construction, maintenance and project management. He came back to finish carpentry full time in 2017. [About Let’s Build Stuff](https://letsbuildstuff.co/about/)