--- title: How to Set a Barn Door Floor Guide description: "On this page[Introduction](#)[Before You Begin](#)[Prerequisites](#)[What You Need To Know](#)[Tools Required](#)[Power Tools](#)[Hand Tools](#)[Supplies](#)[Materials](#)[Installation Steps](#)[Step 1: Find the Center Point](#)[Step 2: Dry Fit the Guide](#)[Step 3: Mark and Pre-Drill](#)[Step 4: Fasten the Guide](#)[Step 5: Test the Door Through Full Travel](#)[Close-Out](#)[Quality Check](#)[Troubleshooting](#)[Door Still…" url: "https://letsbuildstuff.co/learn/set-barn-door-floor-guide/" updated: "2026-09-27" category: General Carpentry tags: - Core Guide - Level 1 --- # How to Set a Barn Door Floor Guide On this page[Introduction](#)[Before You Begin](#)[Prerequisites](#)[What You Need To Know](#)[Tools Required](#)[Power Tools](#)[Hand Tools](#)[Supplies](#)[Materials](#)[Installation Steps](#)[Step 1: Find the Center Point](#)[Step 2: Dry Fit the Guide](#)[Step 3: Mark and Pre-Drill](#)[Step 4: Fasten the Guide](#)[Step 5: Test the Door Through Full Travel](#)[Close-Out](#)[Quality Check](#)[Troubleshooting](#)[Door Still Swings at the Bottom](#)[Door Binds or Drags at the Guide](#)[Guide Works Loose Over Time](#)[Guide Sits Proud of the Floor](#)[Related Guides](#) [Doors & Openings](/learn-category/doors/) Skill Level: [Beginner (Level 1)](/learn/difficulty-levels/#level-1) · Estimated Time: 15-25 Minutes ## Introduction A [barn door](/learn/install-barn-doors/) hangs from an overhead track, a setup [This Old House](https://www.thisoldhouse.com/doors/21097096/how-to-install-a-sliding-barn-door) covers well, but nothing at the bottom holds it flush to the wall unless you add one. The [floor guide](/glossary/doors/#floor-guide-barn-door) is a small bracket screwed to the floor at the doorway that the door straddles as it slides. Without it, the door swings out at the bottom every time someone brushes past it, which stresses the rollers and, over time, can walk the door off the track. This guide covers the floor guide install on its own, the last step in a barn door job, done after the door is already hanging and adjusted. If you are hanging a whole [barn door](https://letsbuildstuff.co/learn/install-barn-doors/) system from scratch, start with the full guide and pick this step up once the door is on the track. Most floor guides are T-shaped or U-shaped, and the door bottom rides in the slot as it opens and closes. A double door setup needs one guide per panel, positioned at each door's own closed position, not one guide shared between both. Skipping this step is an easy way to end up with a callback. A door that swings free at the bottom knocks against [baseboard](/learn/install-baseboard/) and trim every time someone brushes past it, and the constant side load works the rollers loose in the track over time. The guide is a small, inexpensive part, but it is not an optional finishing touch on any barn door job. **Which guide do I need?** - Installing a full barn door system: [How to Install Barn Doors](https://letsbuildstuff.co/learn/install-barn-doors/) - **Adding or fixing just the floor guide: this guide** ## Before You Begin ### Prerequisites - The barn door is already hung on its track and adjusted so it hangs [plumb](/glossary/layout-and-shop-talk/#plumb-level-square-condition) and slides smoothly - Finished flooring is installed at the doorway - You know the door's resting position when closed, so you can center the guide correctly - For a double door, both panels are hung and you have a guide on site for each one ### What You Need To Know - The guide has to sit centered under the door in its closed position, with the door's bottom edge straddling it evenly on both faces - Mounting into a hard floor, tile or hardwood, needs a pre-drilled hole so the screws don't crack the material - On carpet, the guide has to reach through the pile to the subfloor to hold firm - A guide mounted off-center will bind the door against one side of the slot instead of guiding it freely - Check that the guide clears any threshold or transition strip at the doorway before you mark the mounting holes ## Tools Required ### Power Tools - [Drill/driver](/glossary/tools/#cordless-drill) - for driving mounting screws and pre-drilling hard flooring ### Hand Tools - [Tape measure](/glossary/tools/#tape-measure) - Pencil - Torpedo level - to check the guide sits flat, not rocking, on the floor ### Supplies - Guide mounting screws, usually included with the barn door hardware kit ### Materials - Floor guide bracket, from the barn door hardware kit (one per panel on a double door) ## Installation Steps ### Step 1: Find the Center Point Close the door fully and mark the floor directly under the point where the door's bottom edge sits when closed. Measure from the door's leading edge, the edge nearest the latch or pull, to find the guide's exact position, matching the spacing the hardware kit calls for. ### Step 2: Dry Fit the Guide Set the guide on the floor without fastening it, and slide the door closed over it. Check that the door bottom straddles the guide evenly, with the same small clearance on each face. Adjust the guide's position until it does before you mark anything permanent. ### Step 3: Mark and Pre-Drill With the guide positioned correctly, mark the screw hole locations on the floor. On tile, stone, or hardwood, pre-drill each hole so the screws don't crack the material. On carpet, part the pile at each mark instead. ### Step 4: Fasten the Guide Drive the mounting screws to secure the guide to the floor. Check it with a torpedo level; it should sit flat with no rocking. A guide that rocks will work loose over time and stop doing its job. ### Step 5: Test the Door Through Full Travel Slide the door open and closed several times, checking that it straddles the guide the whole way without binding or lifting off the floor. Confirm the door no longer swings away from the wall at the bottom when you push on the face of it. On a double door, repeat the whole process for the second panel. ## Close-Out Sweep up any drilling debris around the doorway, and wipe down the guide and the door bottom if dust settled on them while you worked. This is a fast, self-contained task, so leave the area exactly as clean as you found it. ## Quality Check - Guide is centered under the door in the closed position - Door bottom straddles the guide evenly on both faces - Guide sits flat on the floor with no rocking - Door no longer swings away from the wall when pushed - Door slides through full travel without binding on the guide ## Troubleshooting ### Door Still Swings at the Bottom The guide is out of position, or the door bottom is not actually engaging it. Recheck the door's closed position against the guide and reposition it if there is a gap on either side. ### Door Binds or Drags at the Guide The guide is mounted too tight against one face of the door. Loosen the screws, shift the guide slightly, and retest before fully re-tightening. ### Guide Works Loose Over Time Usually means the screws didn't reach solid material, especially on carpet over a soft subfloor. Re-drive with longer screws into the subfloor itself, not just the underlayment. ### Guide Sits Proud of the Floor On thick carpet or an uneven transition, a guide that isn't fully seated will catch feet and vacuum cleaners, not just the door. Recheck that it's screwed down flush rather than resting on top of the pile, and shim underneath on an uneven subfloor rather than letting the guide rock on a high spot. ## Related Guides - [How to Install Barn Doors](https://letsbuildstuff.co/learn/install-barn-doors/) - [How to Install Bypass Doors](https://letsbuildstuff.co/learn/install-bypass-doors/) - [How to Finish a Bypass Door Install](https://letsbuildstuff.co/learn/bypass-door-final-install/) - [How to Install 8'0" Bi-Fold or Bypass Door Slabs](https://letsbuildstuff.co/learn/install-bifold-bypass-slabs-80/) - [How to Install a 6'8" Bi-Fold or Bypass Door Frame](https://letsbuildstuff.co/learn/install-bifold-bypass-frame-68/) Written by **David Hospodka**, Sun’s Up Construction David Hospodka learned finish carpentry from his father, alongside his brother Joel, and worked his way through college trimming houses. He then spent about ten years as a railroad bridge engineer, handling design, construction, maintenance and project management. He came back to finish carpentry full time in 2017. [About Let’s Build Stuff](https://letsbuildstuff.co/about/)